| Wago Main Page |
| I/O Products |
|
| Fieldbus Coupler |
| Programmable Feildbus Controller |
| Digital Input Modules |
| Digital Output Modules |
 |
| 1 Channel |
| 230V AC, 16A, relay 1a |
| 2 Channel |
| 24V DC,
0.5A |
| 24V DC, 2.0A |
| 24V DC,
0.5A, diagnostics |
| 24V DC,
2.0A, diagnostics |
| 24V DC,
EEx i |
| 125V AC,
0.5A, relay 2 CO contacts, pot. free |
| 230V AC,
1.0A relay 2 CO contacts, pot. free |
| 230V AC,
0.3A, solid state relay |
| 230V AC,
3.0A, solid state relay for 30s |
| 230V AC,
2.0A, relay 2 NO |
| 230V AC,
2.0A, relay 2 NO, pot. free |
| 4 Channel |
| 5V DC, 20
mA |
| 24V DC,
0.5A |
| 24V DC,
0.5A, 2-conductor |
| 24V DC,
0.5A, low-side switching |
| 8 Channel |
| 24V DC,
0.5A |
|
|
| Analog Input Modules |
| Analog Output Modules |
| Specialty Modules |
| System Modules |
| Approvals |
|
| Wago Digital Output Modules |
 |
| Part Number |
Conformity Marking |
Approvals |
 750-535 |
 |
TÜV (EEx i) |
| Only use this modue lin connection with the 24V DC EEx i supply module (
750-625 ) |
| 2-CHANNEL ANALOG OUTPUT MODULE DC 24 V POSITIVE SWITCHING SHORT-CIRCUIT PROTECTED CARRIER RAIL DIN 35 |
The digital output module directly controls 2 actuators operating in hazardous environments of Zone 1, such as intrinsically safe magnetic valves. The WAGO-I/O-SYSTEM 750 has to be installed in Zone 2 or in non-hazardous environments. All outputs are electronically short-circuit-protected.
Indicators: Green LED (output status)
Each input is electrically isolated from the bus by use of optocouplers.
Note: Only use the digital input module in connection with the 24 V DC EEx i supply module
750-625 . |
|
| Power Supply Instructions |
When operating the intrinsically safe EEx i modules in connection with sensors/ actuators operating in hazardous environments of Zones 0 and 1, the supply module 24V DCEEx i (
750-625 ) must be used to supply the I/O modules.
Note:
If further 24V DC EEx i supply modules are required, four separation modules (
750-616 ) must be placed between the intrinsically safe sections. |
|
| Technical Information |
| Characteristic |
Value |
| No. of outputs |
2 |
| CURRENT CONSUMPTION (INTERNAL) mA |
7 mA |
| Voltage via power jumper contacts (max) |
SUPPLY VIA DC 24.7 V EEX I SUPPLY MODULE
750-625 |
| Type of load |
resistive, inductive, lamps |
| Max. switching frequency (kHz) |
1 kHz |
| Output data |
DC 24 V, Ri = 285 Ohm |
| Power consumption P max. |
2.1 W (WITH AN OUTPUT CURRENT OF 40 mA) |
| Power loss Pv |
1.1 W (WITH AN OUTPUT CURRENT OF 40 mA) |
| Input current typ. (field side) |
8.5 mA / MODULE + LOAD |
| Isolation |
375 V System / Supply |
| Internal data width (Bit) |
2 Bit |
| Operating temperature |
0 °C ... + 55 °C |
| Storage temperature |
-25 °C ... +85 °C |
| Relative air humidity |
95% |
| Vibration resistance |
acc. IEC 60068-2-6 |
| Shock resistance |
acc. IEC 60068-2-27 |
| Degree of protection |
IP 20 |
| EMC immunity to interference |
gem. EN 61000-6-2 (1999) |
| EMC emission of interference |
gem. EN 61000-6-4 (2002) |
| Conformity marking |
CE |
| EC EMC standards |
89 / 336 / EWG |
|
| Characteristic |
Value |
| EC low voltage standards |
73 / 23 / EWG |
| Ex guideline |
94 / 9 / EG; EN 50014, EN 50020, EN 50021 |
| Marking |
Ex II 3 (2) GD Eex nA [ib] IIC / IIB T4 |
| Electrical circuit, relevant safety data |
U0 = 27,3 V; I0 = 106 mA; P0 = 723 mW; CHARACTERISTIC: LINEAR |
| Intrinsically safe / EEx ib IIB / EEx ib IIC |
L0 / 12 mH / 3 mH |
| Intrinsically safe / EEx ib IIB / EEx ib IIC |
C0 / 680 nF / 88 nF |
| Cross section from [mm²] |
0.08 mm² |
| Cross section to [mm²] |
2.5 mm² |
| Cross section from [AWG] |
28 AWG |
| Cross section to [AWG] |
14 AWG |
| Weight |
48.5 g |
| Color |
blue |
| Height |
64 mm |
| Height |
2.52 in |
| Width |
12 mm |
| Width |
0.472 in |
| Depth |
100 mm |
| Depth |
3.937 in |
| Strip length from |
8 mm |
| Strip length to |
9 mm |
| Strip length |
0.33 in |
|
|
|
